7 inch colour reversing camera system for motorhomes
7 inch colour reversing camera system for motorhomes
7 inch colour reversing camera system for motorhomes

7 inch colour reversing camera system for motorhomes

£164.00
(Inc. 20% VAT)
(£136.67 Exc. VAT)
In stock
+
Weight
2 kg
Introduction to product

We designed this reversing camera specifically for motorhomes and caravans to reduce the size of hole required in fitting the camera. By gluing the camera to the vehicle only a small 8mm diameter hole needs to be drilled to allow the cable to enter the vehicle. The monitor is our high resolution colour MON509D which is supplied with a foot style bracket The camera is one of our standard CCD reversing cameras with a stainless steel bracket. They give excellent picture during the day and the night vision is good.

Specification of monitor
  •    Screen size:7 inch (diagonal length)
  •    Brand new LCD panel, high resolution
  •    [16 : 9 ] wide screen display
  •    2 video inputs
  •    PAL & NTSC auto-switching
  •    Resolution:800 x R.G.B x 480 dots
  •    Power supply: DC 12 V/24V auto switching
  •    Remote control, OSD menu;
  •    4 PIN connectors
  •    View angle range:(left/right) 65º (top) 40º (down) 15º

Supplied with quick release style bracket and 8mm disconnect point for easy removal of monitor.

Specification of camera
  • 1/3 700TVL SONY CCD
  • Video System:- PAL
  • Pixels:- PAL:752(H)*582(V)
  • Horizontal Resolution:-700 TVL
  • Min Illumination:- 0.001Lux (0 Lux IR on)
  • SNR:- ≥50dB
  • Electronic Shutter:- 1-1/10000(S)
  • Video Output:- 1.0V±0.5Vp-p 75Ω
  • View Angle:- 120°  (Unless stated otherwise in information tab)
  • Working Voltage:- DC9V-12V±0.5V
  • Consumption:- 70mA±10%
  • Waterproof Rate:- IP68
Explanation of our options

On all of our reversing camera systems we have a wide variety of cable and power options. The information below shows you what each option means.

5m 7.5m 10m 12.5m 15m 20m

These are our standard 4 pin extension cables. These options allow you to select what length you need. They are listed in metres, to get the length in feet simply multiply by 3 to change. Having longer than you need will not affect the picture, any extra cable should be coiled loosely where it cannot get damaged.

10M 8mm link, 12.5M 8mm link, 15M 8mm link

These are our 12.5m or 15m cables with an 8mm link at the front of the cable - designed to disconnect to help running through any tight gaps, then reconnected at the end of the install once you are next to the monitor.

8mm link for reversing camera extension cable

Bailey adaptor

We do an adaptor to fit the Waeco cables that are pre-installed in Bailey Motorhomes. It converts their cable into our standard 4 pin ones. We have single camera and dual camera versions.

Waeco cable adaptor

Stand style bracket

Stand style bracket

This is useful on our HD series of monitors where a curved dash makes mounting the U-bracket difficult. It also makes it faster and easier to remove the monitor.

Easy wire fuse tap a.k.a "piggyback fuse holders"

These can be used to take power from the fuse board. The earth should be to a point where there is bare metal to the vehicle body. The cable is about 2M long and terminates in a 2.1mm/5.5mm power plug, which fits in to the corresponding socket on the monitor wiring.  We stock these in different blade sizes, please select the type of fuse tap that is fitted to your fusebox.

Fuse tap

 

Model
HR705M
Bar Code
5060342258250
Vehicle
Motorhome
Voltage
12/24 volt
Screen size
7" diagonal
Screen resolution
800 x 480 pixels
Connector type
4 pin aviation
TVL
700 TVL
Special features
8mm link to reduce hole sixes
Type of sensor
CCD
Sensor manufacturer
Sony
Sensor size
1/3" sensor
Camera angle
120 degrees